Viking VIL1200 Manuel d'utilisateur télécharger pdf (Page 1)

VIKING MODEL VIL1200

INLINE FAN

ONLY FOR USE WITH: VWH, VIH, VBCV, VICV, DTWL AND

DTWN 24"W TO 66"W WALL AND ISLAND HOODS

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-

JURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac-

turer. If you have questions, contact the manufacturer or

your distributor.

2. Before servicing or cleaning unit, switch power off at ser-

vice panel and lock the service disconnecting means to pre-

vent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the

service panel.

3. Installation work and electrical wiring must be done by

a qualiﬁ ed person(s) in accordance with all applicable

codes and standards, including ﬁ re rated construction

codes and standards.

Sufﬁ cient air is needed for proper combustion and ex-

hausting of gases through the ﬂ ue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer’s guidelines and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5 When cutting or drilling into wall, or ceiling, do not

damage electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of ﬁ re, use only metal ductwork.

8. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, construction

dust, etc. off power unit.

3. Please read speciﬁ cation label on product for additional

information and requirements.

4. Unit has an unguarded impeller. Do not use in locations where

the impeller is readily accessible to people or animals.

5. Screen guards must be installed if impeller is within reach

of personnel, and less than 7 feet above the ﬂ oor.

6. When handling fan wear hand protection and stay

clear of sharp edges.

7. Because this unit has rotating parts, safety should be

exercised during all phases of installation, operation and

maintenance.

8. The motor is permanently lubricated. Do not oil or disas-

semble motor.

9. Electrical circuit, including speed control, (if used), must

be rated 5.0 AMPS minimum.

SPECIFICATIONS

MODEL

VOLTS

AMPS

CFM

DUCT SIZE

IL1200

115

4.84

1200

10” DIA.

INSTALLER: Leave this Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

1 2 3 4

Résumé du contenu

Page 1 - INLINE FAN

VIKING MODEL VIL1200INLINE FANONLY FOR USE WITH: VWH, VIH, VBCV, VICV, DTWL ANDDTWN 24"W TO 66"W WALL AND ISLAND HOODSREAD AND SAVE THESE IN

Page 2 - PLANNING THE INSTALLATION

PLANNING THE INSTALLATION1. Locate the inline fan so that the length of the duct run and number of elbows needed is kept to a minimum.2. The inlin

Page 3 - ROUGH-IN PLATE

CONNECT WIRING TO VIL1200 INLINE FAN1. The opposite end of this wiring will be connected to the rough-in plate in the next step.2. Remove wiring bo

Page 4 - VIKING RANGE CORPORATION

CONNECTING DUCT WORK TO VIL1200 INLINE FANTwo duct clamps part number 001377-000 are included with this unit and are intended to simplify fan installa

Commentaires sur ces manuels

Pas de commentaire

Viking VIL1200 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Serre-câbles Viking VIL1200. Viking VIL1200 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels