Viking Alarm Dialers Manuel télécharger pdf (Page 5)

Enter one digit from 0-9 followed by #92. If the ring delay is set to 0, ring detection is disabled, so that the K-202-

DVA will not answer incoming calls. It is important to note that this prevents Remote Access and Remote Pro-

gramming.

L. Ring Delay

The security code allows the user/installer to program the K-202-DVA either locally or remotely. The factory set

security code is 845464 (V-I-K-I-N-G). It is recommended that the security code be changed. Example: To store

654321 as the security code:

J. Security Code (memory location #90)

Step 1. Access programming as shown in Programming section A.

Step 2. Enter 654321 #90.

Step 3. Exit Programming as shown in section A.

Note: The security code must be 6 digits, cannot include a

or a #, and cannot be set the same as the remote

access code.

Enter a six-digit access code followed by #91. Note: The remote access code must use only the digits 0-9, cannot

contain

or #, and cannot be set the same as the security code.

K. Remote Access Code

Enter two digits from 01-99 followed by #93.

M. Ringback Limit

Call Progress Detection is enabled by setting the Forced Play Timer to 0, which is done by entering the two digits

00 followed by #94. Call Progress Detection is disabled by setting the Forced Play Timer to a non-zero value from

1 to 99 seconds. Enter a two digit number from 01- 99 followed by #94.

N. Forced Play Timer and Call Progress Detection

Enter 2 digits + #X9, where X is the input number (1-2).

First Digit: 0 = normally open

1 = normally closed

2 = enabled

3 = disabled

Note: These parameters should be set for each input being used. If contacts are disabled through programming

30/31#X9, they must be enabled with 20/21 #X9 before they will function. This allows wiring and contact style

changes without causing false alarms.

F. Contact Closures

Second Digit: 0 = momentary closure

1 = continuous closure

Enter 4 digits + #X0, where X is the input number (1-2)

First two digits: 01 - 99 are the Message Repeat Counter

Last two digits: 01 - 99 are the Lap Counter

Note: Each input can have its own Message Repeat Counter and Lap Counter.

G. Message Repeat Counter and Lap Counter

Enter 6 digits + #XQ, where X is the input number (1-2). The format is 2 digits for hours, 2 digits for minutes, and

2 digits for seconds: HHMMSS. The qualifier timer can be set anywhere from zero to 18 hours, and has a 1

second resolution. Note: Each input has its own Qualifier Timer.

H. Qualifier Timer

Enter 6 digits + #X#, where X is the input number (1-2). The format is 2 digits for hours, 2 digits for minutes, and

2 digits for seconds: HHMMSS. The resume timer can be set anywhere from zero to 18 hours, and has a 1 second

resolution. Note: Each input has its own Resume Timer.

I. Resume Timer

Recording of the voice messages may be done either locally or remotely. Once programming has been entered,

touch tones are used to start and stop the recording process. To start a recording: enter Q followed by the number

of the input. The K-202-DVA gives a single beep to indicate that it is recording and then starts the recording

process. Speak into the handset of the telephone to record the message. The K-202-DVA has a maximum mes-

sage time for each input of one minute. When finished recording the message, enter any touch tone to stop the

recording process. At this point the K-202-DVA automatically plays back the message just recorded. If the record-

ing process goes over one minute the K-202-DVA stops the recording and starts playing back the message. To

clear a single message: enter Q followed by the number of the input and then immediately press any Touch Tone

to stop the recording process.

O. Recording Messages

When in programming, enter Q0 followed by the number of the input to play back the message recorded

for that input. If no message has been recorded, nothing will be heard.

P. Playing Back Messages

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Viking Alarm Dialers Manuel Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Viking Alarm Dialers